Are you currently looking for answers about A Step-by-Step Guide to Installing a Bathtub?
Installing a tub isn't precisely rocket science, but it does require strong plumbing, woodworking, and occasionally, tiling skills. Changing an old bathtub with a new one is likewise a moderately difficult project. If the old bathtub is conveniently easily accessible, the task can relocate immediately; if you need to open a wall to get rid of the old tub and also place the new bath tub, the task is a lot harder. In either instance, the job is within a house handyman's abilities, although you will require a helper to move out the old bathtub and also set in the new one. Ensure you have actually qualified on your own for the job as well as fit attempting it. Rather than employing a professional to take over a halfway-completed project, it is much better to consider employing one before you start. Possibilities are you may require a specialist plumber to make tube links.
This short article will certainly aid you mount a brand-new bathtub in your washroom if you have currently acquired a new bathtub as well as do not need to transform the setup of your previous supply of water pipes.
Your devices as well as product list ought to make up the following:
Preparing for the Setup
First of all, the sustaining frame provided with the bathroom needs to be fitted (if required) according to the producer's guidelines. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is important to see to it that if the faucet features a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps unit to avoid strain on the bathtub.
Fit the versatile tap adapters to the bottom of both faucets using 2 nuts as well as olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet via the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you use all of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bath ought to now prepare to be fitted in its last placement.
Removing Old Taps
If you require to change old taps with new ones as a part of your setup, then the first thing you need to do is detach the supply of water. After doing so, turn on the taps to drain any kind of water remaining in the system. The process of eliminating the existing faucets can be fairly bothersome because of the limited gain access to that is commonly the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the faucets. Have a cloth all set for the continuing to be water that will come from the pipes. As soon as the supply pipelines have actually been removed, use the exact same device to loosen the nut that holds the taps onto the bath/basin. You will require to quit the solitary faucets from transforming during this procedure. Once the taps have actually been removed, the holes in the bath/basin will have to be cleaned of any old sealing substance.
Before carrying on to fit the brand-new taps, compare the pipeline connections on the old faucets to the brand-new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new faucets to fit.
Setting up the Bath tub
Making use of both wood boards under its feet, put the bathtub in the needed position. The wood boards are practical in uniformly spreading out the weight of the bathtub over the location of the boards rather than concentrating all the weight onto four tiny points.
The following objective is to guarantee that the tub is leveled all round. This can be achieved by checking the spirit level and also changing the feet on the bathtub till the spirit level reviews degree.
To mount taps, fit all-time low of the furthest adaptable tap connector to the suitable supply pipe by making a compression join; then do the same for the various other faucet.
Switch on the supply of water as well as check all joints and brand-new pipework for leaks as well as tighten them if required. Load the tub and additionally examine the overflow outlet and also the typical outlet for leaks.
Finally, fix the bathroom paneling as explained in the manufacturer's instruction manual. Tiling and also securing around the bathtub ought to wait up until the tub has been made use of at least when as this will settle it right into its final position.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic connector to avoid damages to the thread. One end of the port fits on the plastic tail of the tap and the various other end gives a connection to the current supply pipelines.
If you require to fit a monobloc, then you will require lowering couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the installing hole in the bath/basin making certain that the washing machines are in area between the faucet and also the sink. Protect the faucet in place with the supplier offered backnut. When the tap is safely in position, the supply pipelines can be attached to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with regular tap adapters. The previous kind should be linked to the faucet ends initially, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bath meets the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is necessary as the installation can relocate sufficient to crack a rigid seal, triggering the water to pass through the wall surface in between the bathroom as well as the tiling, resulting in problems with moisture and also possible leaks to the ceiling listed below.
You can choose from a selection of coloured sealants to assimilate your fixtures as well as fittings. They are offered in tubes and also cartridges, as well as can sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked paper or soft rope. Bear in mind to constantly fill the bathtub with water prior to securing, to enable the motion experienced when the tub remains in use. The sealant can break relatively early if you do not consider this motion before securing.
Conversely, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are additionally conveniently readily available on the marketplace. It is a good idea to fit the tiles using waterproof or water resistant adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I ran across that piece of writing about How to Install a Bathtub Yourself when doing a lookup on the search engines. Remember to take a moment to share this page if you enjoyed it. Bless you for your time. Please come by our site back soon.
Choose excellence in emergency plumbing.